点击图片查看原图
泰州INA轴承压入轴承时应灵活无堵塞。如果旋转不明显，则表明轴尺寸过大，应减小公差。如果推力圆柱滚子轴承有明显的“沙”感，那么当推力圆柱滚子轴承被手动旋转并压入轴时，它可能对轴太宽容或者轴的圆度不好。因此，为了控制轴和轴承腔的公差，应控制圆度。目前，国内许多厂家只控制公差，而不是圆度。
Taizhou INA bearing shall be flexible and non clogged when pressing into bearings. If the rotation is not obvious, it indicates that the shaft size is too large, and the tolerance should be reduced. If thrust cylindrical roller bearings have obvious "sand" feeling, then when thrust cylindrical roller bearings are manually rotated and pressed into the shaft, it may be too tolerant to the shaft or the roundness of the shaft is not good. Therefore, in order to control the tolerance of the shaft and bearing chamber, the roundness should be controlled. At present, many domestic manufacturers only control tolerance, not roundness.
由于泰州INA轴承是高精度产品，装配不当容易造成轴承滚道损坏，导致轴承损坏。推力圆柱滚子轴承应装配特殊模具。他们不能随意敲门。他们只能迫使小环进入轴，大环应按下大环。装配时，须使用气压或液压。装配时，上模和下模应为水平模。如果有倾角，轴承滚道会受到力的破坏，轴承将获得良好的引导。
Because Taizhou INA bearing is a high-precision product, improper assembly is easy to cause bearing raceway damage, leading to bearing damage. Thrust cylindrical roller bearings should be assembled with special moulds. They can't knock at random. They can only force the small ring into the shaft, and the large ring should press the large ring. When assembling, air pressure or hydraulic pressure must be used. When assembling, the upper and lower die should be horizontal die. If there is inclination, the bearing raceway will be damaged by force and the bearings will be well guided.
1。轴承温度升高应如何处理？
1. How should the bearing temperature rise be handled?
当轴承温度升高时，首先确定操作是否错误。
When the bearing temperature rises, first determine whether the operation is wrong.
（1）检查机油的标准油位是否正常。如果异常，检查漏油阀是否密封。如果关闭，应该添加油。如果垫圈渗出，应该关闭。
(1) check whether the standard oil level of the oil is normal. If abnormal, check whether the oil leakage valve is sealed. If shut down, oil should be added. If the gasket is exuded, it should be closed.
（2）样品油颜色是否有变化，进行实验室检查，看看泰州INA轴承是否变质。如果确认恶化，应更新的油脂。
(2) whether there is any change in the color of the sample oil. Do laboratory tests to see if the INA bearing of Taizhou is deteriorating. If the deterioration is /confirm/ied, the oil should be renewed.
（3）检查轴承是否有异常声音，并检测轴承摆动是否异常。
(3) check whether the bearing has abnormal sound and detect whether the bearing swing is abnormal.
（4）检查调速器的液压。如果油压较低，则可以关闭冷凝水液压阀。
(4) check the hydraulic pressure of the governor. If the oil pressure is low, the condensate hydraulic valve can be turned off.
（5）检查冷凝水压力、电流及管路系统是否正常。如果水压较低，可能会堵塞过滤，而不能及时处理。这台机器可以关机。当确认它能工作时，它将再次投入使用。
(5) check the condensate pressure, current and piping system is normal. If the water pressure is low, it may clog up filtration, but not deal with it in time. This machine can be turned off. When it is confirmed that it can work, it will be put into use again.
2。首先，让我们来看看轴承温度升高的原因。
2. First of all, let's take a look at the cause of the temperature rise of the bearing.
（1）可能是泰州INA轴承油质量劣化、污油或油变质。例如，油中含水量的增加将导致油度的增加，减少润滑油的润滑，使轴承衬套腐蚀，导致轴承温度的升高。
(1) it may be Taizhou INA bearing oil quality deterioration, dirty oil or oil deterioration. For example, the increase of water content in oil will lead to the increase of oil acidity, reduce the lubrication of lubricating oil, make the bearing bushing corrode, and lead to the increase of bearing temperature.
（2）可能是由于轴承冷凝水的中断引起的。
(2) it may be caused by interruption of bearing condensate.
由于轴承是高精度产品，装配不当容易造成轴承滚道损坏，导致轴承损坏。推力圆柱滚子轴承应装配特殊模具。他们不能随意敲门。他们只能迫使小环进入轴，大环应按下大环。装配时，须使用气压或液压。装配时，上模和下模应为水平模。如果有倾角，轴承滚道会受到力的破坏，轴承将获得良好的引导。
Because the bearing is a high-precision product, improper assembly is easy to cause bearing raceway damage, resulting in bearing damage. Thrust cylindrical roller bearings should be assembled with special moulds. They can't knock at random. They can only force the small ring into the shaft, and the large ring should press the large ring. When assembling, air pressure or hydraulic pressure must be used. When assembling, the upper and lower die should be horizontal die. If there is inclination, the bearing raceway will be damaged by force and the bearings will be well guided.
文章来自：泰州SKF轴承 www.wh-skf.com
The article is from: Taizhou SKF bearing www.wh-skf.com
文章来自：泰州INA轴承 www.ina-china.cn
The article is from: Taizhou INA bearing www.ina-china.cn
文章来自：泰州NSK轴承 www.klbbearings.com
The article is from: Taizhou NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672
